Modular Engine Factory Layout (2024)

Welcome to another Super Efficient Build Guide, today we will be producing 5 modular engines per minute, to be later used in thermal propulsion engines. To accompany this written guide there will also be a video guide which you can find in the link below.

Video Guide: Modular Engines Super Efficient Build Guide

Requirements:

For this build we will be using a total of:

• 120 Iron ore
• 30 Rotors
• 20 Stators
• 112.5 Crude oil

We will also need resources to build the following:

• 5 Manufacturers
• 6 Refineries
• 9 Assemblers
• 8 Constructors
• 4 Smelters
• And a single Awesome sink.

This build will be done on a 13 x 18 grid and once up and running will cost no more than 668Mw
Take note that at the bottom of the grid we have the iron ore brought up in the 7th column in the brown box, followed by the rotors in the 8th column in white, then stators in the9th column coloured in turquoise followed by crude oil in the 10th column.
During this build you will also need a maximum belt speed of mk2 however I’ll be using Mk3s across the build.
In order to give you as much creative freedom, I will be covering the basic layout, feel free to move things around should you wish, to help you, I will list what’s going on at the start of each section.

Part 1. Iron Production

First we will sort out the iron production. The iron ore will run to four smelters, of which three will be dedicated to iron plates, leading to three constructors. The fourth smelter will run iron to a screw production line, which will use two constructors to produce iron rods, followed by three constructors for screws. The screws and plates will then be run to two assemblers to produce reinforced iron plates.
The four smelters will be placed in the middle of the fourth column of the second row, and will be placed up to the seventh row. These will all be set to iron, with the first smelter running the iron to a splitter followed by two constructors that span the first and second, and second and third column of the fourth row. These will both be set to iron rods before merging and then splitting between three more constructors that will be placed in the first, second and third column of the sixth row. These three constructors will be set to screws and then merge into a manifold line which will feed the two assemblers that span the first and second and third and fourth column starting in the ninth row. These will both be set to reinforced iron plates.

Next in front of the three remaining smelters back in the second row we shall place three more constructors which will be set to iron plates. I’ve placed these three constructors in line with the screw constructors directly in front of the three smelters. These constructors will run the iron plates up into the assemblers along with the screws. We will then merge the reinforced iron plates with them facing the left of the grid.

Part 2. Assembler Lines.

Set all these Assemblers to smart plating with all the outputs merging to the left of the build.

Next we shall place two more assemblers. One in the eighth column of the 11th row, and then the second spanning the ninth and tenth column. These will both be set to motors and should be fed with the 20 rotors and 20 stators These will then be merged and sent onto the manufacturers. If you have just the ten motors, send these directly up to the manufacturing line.

Part 3. Rubber Production

This section will have three point seven five refineries producing rubber to go on to the modular engines with the heavy oil residue heading to one point eight seven five refineries turning the excess oil into petroleum co*ke to be sunk.

At this point we will need to turn the crude oil into rubber, first we shall place four refineries facing the right of the build starting in the ninth column of the second row. These will all be set to rubber with one of the refineries being set at 75% clock speed. The rubber will then be merged and run up to the top of the build. I should mention at this point, that I have added two more refineries. These have been placed in the eight row and are producing petroleum co*ke from the heavy oil residue. This is then sunk in the awesome sink. One of these refineries needs to be set at 87.5% clockspeed.

Part 4. Modular Engines Production line.

To finish off this build we will need to place five manufacturers in the First column through to the 11th column in the 17th row. These need to be set to modular engines with the outputs merged and then sent to storage, on the front side we will also need another manifold line. The first line will be fed by the smart plating, the second line by motors and the third line by rubber.

Once done you should have a fully functioning plant that produces a total of Five modular engines per minute.

We’re very proud to have launched this website and hope you have found the guide both helpful and enjoyable.We look forward to updating the site weekly with new guides and layouts.

If you have a particular layout or guide you’d be interested in sharing with the community, we’d gladly giveyou the chance to be an author on our site, get in touch with us.